Quick-Fit Ducting

Nordfab Quick-Fit ducting is used in a wide variety of dust collection, fume extraction, and process ventilation applications. Quick-Fit modular clip-together ducting system with rolled edges saves time and money on installation, is easy to clean out, is adaptable to existing ductwork, and is easily re-used during shop floor reconfigurations – providing one of the lowest life cycle costs of any ducting product. Ductwork is available in galvanised and stainless steel construction.

Quick-Fit 60 Degree Segmented Bend R=1.5

Quick-Fit (QF) clamp-together duct 60° Segmented Bends. Ø350 - 710 mm in galvanised steel or Ø80 - 710 mm in 304SS construction. Nordfab's Quick-Fit (QF) bends allow airflow direction change in a run of a duct.
Find out more

Quick-Fit 90 Degree Segmented Bend R=1.5

Quick-Fit (QF) clamp-together duct 90° Segmented Bends. Ø350 - 710 mm in galvanised steel or Ø80 - 710 mm in 304SS construction. Nordfab's Quick-Fit (QF) bends allow airflow direction change in a run of a duct.
Find out more

Quick-Fit 15 Degree Pressed Bend R=1.5

Quick-Fit (QF) clamp-together duct 15° Bends. Ø80 - 315 mm, galvanised steel construction. Nordfab's Quick-Fit (QF) bends allow airflow direction change in a run of a duct.
Find out more

Quick-Fit 30 Degree Pressed Bend R=1.5

Quick-Fit (QF) clamp-together duct 30° Bends. Ø80 - 315 mm, galvanised steel construction. Nordfab's Quick-Fit (QF) bends allow airflow direction change in a run of a duct.
Find out more

Quick-Fit 45 Degree Pressed Bend R=1.5

Quick-Fit (QF) clamp-together duct 45° Bends. Ø80 - 315 mm, galvanised steel construction. Nordfab's Quick-Fit (QF) bends allow airflow direction change in a run of a duct.
Find out more

Quick-Fit 60 Degree Pressed Bend R=1.5

Quick-Fit (QF) clamp-together duct 60° Bends. Ø80 - 315 mm, galvanised steel construction. Nordfab's Quick-Fit (QF) bends allow airflow direction change in a run of a duct.
Find out more

Quick-Fit 90 Degree Pressed Bend R=1.5

Quick-Fit (QF) clamp-together duct 90° Bends. Ø80 - 315 mm, galvanised steel construction. Nordfab's Quick-Fit (QF) bends allow airflow direction change in a run of a duct.
Find out more

Quick-Fit (QF) Duct Lockformed 1.5m

Nordfab Quick-Fit (QF) ducting with a lockformed seam in 1,5 meters length of duct is available in 0,7 - 0,9 mm thick galvanised or stainless steel, ranging from 80 - 710 mm in diameter.
Find out more

QF Slip Duct

The Quick-Fit (QF) Slip Duct is sometimes referred to as slip joint, telescopic piece, telescope, or make up piece. It is being used to provide variable length adjustment of a Quick-Fit system by eliminating precise measurements.
Find out more

Quick-Fit (QF) Clip Premium

Nordfab Quick-Fit (QF) Clips allow quick and easy connection during installation as well as subsequent removal and re-use of QF components. The internal gasket quarantees a tight joint. Clips come from factory with Nitrile seals. Available in galvanised steel, ranging from 80 mm to 710 mm in diameter.
Find out more